Tungsten carbide coil winding nozzle - coil winding nozzle_coil winding tensioner_tungsten carbide nozzle_ruby nozzle_magnetic tensioner_magnet damper_ceramic eyelet

Product Category

Products

Product name：Tungsten carbide coil winding nozzle
Product ID：101

Description

Specification table of Tungsten carbide nozzle

No	Item	Name	Model No.(mm)
No	Item	Name	L	L1	D	D1	d1	d2		H
T2 Series
1	T2-001	TH2010-040-350100	35	10	2	1.0	0.4	0.4		---
2	T2-002	TH2012-050-350100	35	10	2	1.2	0.5	0.5		---
3	T2-003	TH2012-040-35070	35	7	2	1.2	0.4	0.4		---
4	T2-004	TH86-020-20020	20	2	0.8	0.6	0.2	0.2		---
5	T2-005	TH1510-050-30070	30	7	1.5	1	0.5	0.5		---
6	T2-006	TH2010-050-30070	30	7	2		0.5	0.5		---
7	T2-007	TH2012-050-350100	35	10	2	1.2	0.5	0.5		---
8	T2-008	TH2010-040-35070	35	7	2	1	0.4	0.4		---
9	T2-009	TH208-030-30080	30	8	2	0.8	0.3	0.3		---
10	T2-010	TH2010-2-1007	26	7	2	1	0.3	0.3		---
11	T2-011	TH2010-050-300100	30	10	2	1	0.5	0.5		---
12	T2-012	TH2520-080-350110	35	11	2.5	2	0.8	0.8		---
13	T2-013	TH2010-030-30060	30	6	2	1	0.3	0.3		---
14	T2-014	TH2012-060-350150	35	15	2	1.2	0.6	0.6		---
T3 Series
1	T3-001	TH3010-030-30070	30	7	3	1.0	0.3		0.3		---
2	T3-002	TH3010-040-30070	30	7	3	1.0	0.4		0.4		---
3	T3-003	TH3010-050-300100	30	10	3	1.0	0.5		0.5		---
, 4	T3-004	TH3010-050-300100	30	10	3	1	0.5		0.5		---
5	T3-005	TH3010-060-30080	30	8	3	1	0.6		0.6		---
6	T3-006	TH308-030-30070	30	7	3	0.8	0.3		0.3		---
7	T3-007	TH3013-060-30090	30	9	3	1.3	0.6		0.6		---
8	T3-008	TH3015-060-14090p	14	9	3	1.5	0.6		0.6		5
9	T3-009	TH3015-100-14090p	14	9	3	1.5	1		1		5
10	T3-010	TH3010-040-14090p	14	9	3	1	0.4		0.4		5
11	T3-011	TH300-100-3000	30	---	3	---	1		1		---
12	T3-012	TH300-030-2600	26	---	3	---	0.3		0.3		---
13	T3-013	TH300-060-2600	26	---	3	---	0.6		0.6		---
14	T3-014	TH300-120-3000	30	---	3	---	1.2		1.2		---
15	T3-015	TH300-120-3000	30	---	3	---	1.2		1.2		---
16	T3-016	TH300-030-3000	30	---	3	---	0.3		0.3		---
17	T3-017	TH300-060-2600	26	---	3	---	0.6		0.6		---
18	T3-018	TH305-030-30040	30	4	3	0.5	0.3		0.3		---
19	T3-019	TH300-080-2500	25	---	3	---	0.8		0.8		---
20	T3-020	TH300-040-3500	35	---	3	---	0.4		0.4		---
21	T3-021	TH300-035-3500	35	---	3	---	0.35		0.35		---
22	T3-022	TH300-100-2500	25	---	3	---	1		1
23	T3-023	TH300-080-4500	45	---	3	---	0.8		0.8		---
24	T3-024	TH300-150-3500	35	---	3	---	1.5		1.5		---
25	T3-025	TH300-100-3600	36	---	3	---	1		1		---
26	T3-026	TH300-060-3000	30	---	3	---	0.6		0.6		---
27	T3-027	TH400-080-3000	30	---	4	---	0.8		0.8		---
28	T3-028	TH400-120-4300p	43	---	4	---	1.2		1.2		20
29	T3-029	TH400-080-3200p	32	---	4	---	0.8		0.8		20
30	T3-030	TH450-120-4300	43	---	4.5	---	1.2		1.2		---
31	T3-031	TH4025-150-430120p	43	12	4	2.5	1.5		1.5		20
32	T3-032	TH3920-080-200190p	20	19	3.9	2	0.8		0.8		19
33	T3-033	TH500-200-2000	20	---	5	---	2		---		---

Coil winding wire guide Hard Alloy Nozzle(TungstenCarbide nozzle)also call wire guide tubes,wire guide eyelets or wire guide needles,it is used on coil winding machine.it is made precisely of hard alloy and enjoys the hardness up to HRA90.Two terminals andinnerle are all receive mirror surface treatment to ensure enameled wire makes no scrape. High hardness, resistance to flexure, block and impact .

Features:
1. High Wear Resistance
This is assured by the choice of materials for wear elements possessing a minimum hardness in excess of Vickers 1, 000 (HRC 70).
2. Scratch-Proofing
Eliminate wire insulation film damage, low friction resistance, stable wire tension. The wire-guiding surfaces are mirror finished by diamond lapping to a surface roughness of 2 -4 micro inches Ra or better, material permit.
3. Straightness and Stiffness
Straightness and Stiffness are defined by the wire exit being concentric and inflexible with respect to the nozzle locating? . In plain terms, the wire should exit from the nozzle concentric to the locating? To within 0.02 mm, with or without load. A geometric characteristic presentation is shown at upper left. Concentricity to within 0.01mm.
4. Precise Exit Radii
Because the coil winding nozzle's Exit Radii governs the angle of the wire exit from one coil to the next, it should be monitored to + / - 0.025 mm. This is done by digital measurement, shown at upper right.